Update camera patch for new OS

Code/Patch/config.txt

@@ -0,0 +1,82 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+dtparam=i2c_arm=on
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+# Automatically load overlays for detected cameras
+# camera_auto_detect=1
+
+# Automatically load overlays for detected DSI displays
+display_auto_detect=1
+
+# Enable DRM VC4 V3D driver
+dtoverlay=vc4-fkms-v3d
+max_framebuffers=2
+
+# Disable compensation for displays with overscan
+disable_overscan=1
+
+[cm4]
+# Enable host mode on the 2711 built-in XHCI USB controller.
+# This line should be removed if the legacy DWC2 controller is required
+# (e.g. for USB device mode) or if USB support is not required.
+otg_mode=1
+
+[all]
+
+[pi4]
+# Run as fast as firmware / board allows
+arm_boost=1
+
+[all]
+start_x=1
+gpu_mem=128

Code/Patch/patch_for_bullseye.sh

@@ -0,0 +1,11 @@
+#!/bin/sh
+current_file=$0
+cd "$(dirname "$current_file")"
+
+sudo cp /boot/config.txt /boot/config-backup.txt
+sudo cp ./config.txt /boot/config.txt
+sudo cp /usr/lib/arm-linux-gnueabihf/libmmal.so /usr/lib/arm-linux-gnueabihf/libmmal-backup.so.backup
+sudo cp ./libmmal.so /usr/lib/arm-linux-gnueabihf/libmmal.so
+
+echo "patched complete! Please reboot the system!"
+