Update camera patch for new OS
This commit is contained in:
parent
e19a76959c
commit
1058608b0c
82
Code/Patch/config.txt
Normal file
82
Code/Patch/config.txt
Normal file
@ -0,0 +1,82 @@
|
||||
# For more options and information see
|
||||
# http://rpf.io/configtxt
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
#dtparam=spi=on
|
||||
|
||||
# Uncomment this to enable infrared communication.
|
||||
#dtoverlay=gpio-ir,gpio_pin=17
|
||||
#dtoverlay=gpio-ir-tx,gpio_pin=18
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
|
||||
# Automatically load overlays for detected cameras
|
||||
# camera_auto_detect=1
|
||||
|
||||
# Automatically load overlays for detected DSI displays
|
||||
display_auto_detect=1
|
||||
|
||||
# Enable DRM VC4 V3D driver
|
||||
dtoverlay=vc4-fkms-v3d
|
||||
max_framebuffers=2
|
||||
|
||||
# Disable compensation for displays with overscan
|
||||
disable_overscan=1
|
||||
|
||||
[cm4]
|
||||
# Enable host mode on the 2711 built-in XHCI USB controller.
|
||||
# This line should be removed if the legacy DWC2 controller is required
|
||||
# (e.g. for USB device mode) or if USB support is not required.
|
||||
otg_mode=1
|
||||
|
||||
[all]
|
||||
|
||||
[pi4]
|
||||
# Run as fast as firmware / board allows
|
||||
arm_boost=1
|
||||
|
||||
[all]
|
||||
start_x=1
|
||||
gpu_mem=128
|
BIN
Code/Patch/libmmal.so
Normal file
BIN
Code/Patch/libmmal.so
Normal file
Binary file not shown.
11
Code/Patch/patch_for_bullseye.sh
Normal file
11
Code/Patch/patch_for_bullseye.sh
Normal file
@ -0,0 +1,11 @@
|
||||
#!/bin/sh
|
||||
current_file=$0
|
||||
cd "$(dirname "$current_file")"
|
||||
|
||||
sudo cp /boot/config.txt /boot/config-backup.txt
|
||||
sudo cp ./config.txt /boot/config.txt
|
||||
sudo cp /usr/lib/arm-linux-gnueabihf/libmmal.so /usr/lib/arm-linux-gnueabihf/libmmal-backup.so.backup
|
||||
sudo cp ./libmmal.so /usr/lib/arm-linux-gnueabihf/libmmal.so
|
||||
|
||||
echo "patched complete! Please reboot the system!"
|
||||
|
BIN
NOTE!!!!!!.pdf
BIN
NOTE!!!!!!.pdf
Binary file not shown.
BIN
Tutorial.pdf
BIN
Tutorial.pdf
Binary file not shown.
Loading…
Reference in New Issue
Block a user